*********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.8.5.2 (Maintenance Release) Release Date : 27th October 2014 Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) Locale : All *********************************************************************************** Note: Firmware file types *.all - upgrade retaining all previous settings *.rst - upgrade and reset to factory default It is recommended to take a configuration backup prior to upgrading the firmware. [New Features] None. [Improvement] VoIP models only: When pressing OK to save the SIP Account settings, the SIP Expiry time would change to Manual with a timeout of "0". This stopped the router from receiving calls and is now corrected. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.8.4 (Maintenance Release) Release Date : 7th April 2014 Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG Locale : All *********************************************************************************** [New Functions] - None [Improvements & Corrected Problems] - Improved : Prevent potential WLAN WUI scan Javascript injection vulnerability. - Corrected : Can not remove old password after setting new password well. - Corrected : Potential buffer leakage issue while handling SNMPv2c "getbulk" request. - Corrected : It may cause memory leakage issue for SIP ACK message. - Corrected : It may cause buffer overwrite issue on "ip igmp_proxy status" and "ip igmp_snoop status". - Corrected : Improved operation of "ip route add" telnet command - Improved : Change "Session Version" in re-invite packet of FAX. - Improved : Add "voip dsp jitterBuffer" telnet command to set VoIP jitter buffer. - Improved : Modify PPP CHAP timeout to 60 seconds. - Improved : It may get wrong switch port link status. - Improved : Add contact header for SUBSCRIBE message of SIP. - Improved : Adjust the priority of expire header for SIP. [End Of File] *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.8.2 (Formal Release) Release Date : 7th August 2008 Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY Refer to www.draytek.co.uk for full product specification *********************************************************************************** Improvements -------------------- - LAN to WLAN connectivity is now enabled if WLAN is enabled from Telnet. - DS Actual PSD/US Actual PSD and Far Current Attenuation/Far SNR Margin are now shown correctly. - The router will reboot when more than 20 entries on Bind IP to MAC are set. - When the wireless function of AP is disabled, the wireless client can now immediately tell that it has gone offline and wired connectivity is uninterrupted. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.8.1 (Formal Release) Release Date : 12th June 2008 Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY Refer to www.draytek.co.uk for full product specification *********************************************************************************** [Improvements & Corrected issues] - Improve wireless performance - Correct telnet command "internet -V" & "internet -u" displaying incorrect information issue - Correct telnet command "ip igmp_proxy set/reset" causing router crash issue - Correct reboot issue caused by nmap tool *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.8.0 (Formal Release) Release Date : 28th February 2008 Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY *********************************************************************************** [New Functions] - New 1.0.8 Wireless driver - wireless WMM and APSD (Power Save) functions - support the buttons of \"bridge\" and \"repeater\" MAC address in Access Point Discovery page - Add software IGMP snooping - Add wireless software IGMP snooping - New telnet command \"sys autoreboot [on/off/hour(s)]\" - Add VPN IKE/IPSec NAT-T function [Improvements & Corrected Problems] - Correct wireless channel mapping - Correct a issue regarding a DHCP renewal problem - Correct an issue with PSTN relaying - Adjust the serverity rating of tear drop attack for mail alerts *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.3.3 (Formal Release) Release Date : 21st November 2007 Firmware Build : Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY ********************************************************************************** [New Functions] - support "vlan" telnet command [Improvements & Corrected Problems] - Correct access list logical error problem - Correct reboot issue for SIOL VOIP when WAN is in DHCP mode - Increase UPNP sessions up to 30 sessions - Improve "#0" switch to PSTN line function under no dial-tone condition for Vigor 2700V (2S1L) and 2700VG (2S1L) *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.3.2 (Formal Release) Release Date : 28th October 2007 Firmware Build : Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY ********************************************************************************** [New Functions] - QoS : Now 8 user defined types are supported (this reduced pre-definded types by 4) [Improvements & Corrected Problems] - Correct that DHCP can't get IP when strict bind - Improve that QoS Inbound enable will drop the RX throughput - Improve VPN pass through issue when use Nortel VPN client *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.3.1 (Formal Release) Release Date : 1st October 2007 Firmware Build : Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY Refer to www.draytek.co.uk for full product specification ********************************************************************************** [New Functions] - support zoneedit to DDNS - support "port" telnet command - support telnet commands to set adsl EC/bitswap parameters (a) adsl bitswap x y (b) adsl fdmec x [Improvements & Corrected Problems] - Improve that show ddns update message on syslog - Correct wireless region code issue for Taiwan - Correct that 2nd subnet(routed) cannot trigger ISDN Backup connection - Correct that windows vista failed to get one IP if it connected with Vigor router at WAN side [Notes] - How to use Telent command to set "User Agent" for VoIP voip sip misc -t val = 0, hides SIP header User-Agent val = 1, shows SIP header User-Agent val = 2, use default User-Agent i.e. DrayTek UA-1.2.3 val = 3, use user-defined User-Agent voip sip misc -u UAValue sets User-Agent to uaValue *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.3 (Formal Release) Release Date : 20th July 2007 Firmware Build : Applicable Models : Vigor2700 / 2700G / 2700V / 2700VG ADSL Firmware : 131701 (UK Standard) 121201/113111 (Alt) Locale : UK ONLY Refer to www.draytek.co.uk for full product specification *********************************************************************************** [New Functions] - Support four SSIDs for Wireless LAN. - Support RFC-3262 for VoIP (MWI (Message Waiting Indicator) and PR-ACK) [Improvements & Corrected Problems] - Correct the issue of DDNS update twice in PPPoE mode. - Improve PPPoE dial speed. - Increase the voice volume of VoIP port. - Improve VoIP stability. - Expand the length of Username and Password from 15 to 63 characters in Mail Alert Setup. - Improve the Telnet command "voip sip misc" to support "User Agent" for VoIP. [Notes] - How to use Telent command to set "User Agent" for VoIP voip sip misc -t val = 0, hides SIP header User-Agent val = 1, shows SIP header User-Agent val = 2, use default User-Agent i.e. DrayTek UA-1.2.3 val = 3, use user-defined User-Agent voip sip misc -u UAValue sets User-Agent to uaValue *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.2 (Formal Release) Release Date : 24th April 2007 Refer to www.draytek.co.uk for full product specification *********************************************************************************** [New Functions ] - Support DHCP with IP Bind MAC. - Add "Near/Far-end Actual Aggregate Transmit Power (ACTATP)" & "Attainable Net Data Rate (ATTNDR)" to Telnet command "adsl status". [Improvements & Corrected Problems] - Improve DDNS log. - Improve the Call Waiting stability. - Correct the wrong wireless MAC address on WUI. - Correct one day delay issue in NTP. - Improve the NTP update in static IP mode. - Correct the DHCP Relay issue when DHCP server is located at WAN side. - Correct the caller ID display issue. - Improve the VOIP codec stability. - Improve the setting for MPoA page. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.1.3 (Formal Release) Release Date : 29th May 2007 Refer to www.draytek.co.uk for full product specification *********************************************************************************** [New Functions ] - Support DHCP with IP Bind MAC. - Add "Near/Far-end Actual Aggregate Transmit Power (ACTATP)" & "Attainable Net Data Rate (ATTNDR)" to Telnet command "adsl status". [Improvements & Corrected Problems] - Improve DDNS log. - Improve the Call Waiting stability. - Correct the wrong wireless MAC address on WUI. - Correct one day delay issue in NTP. - Improve the NTP update in static IP mode. - Correct the DHCP Relay issue when DHCP server is located at WAN side. - Correct the caller ID display issue. - Improve the VOIP codec stability. - Improve the setting for MPoA page. - Improve the VoIP stability when there are two or more ring ports for one SIP account. - Improve the ring detection function of PSTN loop-through. - Improve the stability of PPTP pass-through in ISDN Internet connection. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.1.1 (Formal Release) Release Date : 9th January 2007 *********************************************************************************** - Improve the router stability when Inbound setting on QoS is chosen and wireless is disabled. - Remove '+' sign if it is in the beginning of caller ID. - Improve the VPN interoperability with VPN Tracker on Mac. - Improve the NTP Client stability. - Correct the display of Annex Type on System Status. - Remove the field of Trap Timeout on Management. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7.1 (Formal Release) Release Date : 04th December 2006 *********************************************************************************** [ Changes ] - Improve the DSL interoperability when get OAM cell. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.7 (Formal Release) Release Date : 1st November 2006 *********************************************************************************** [New Functions] - Support DSL ATM QoS PCR/SCR/MSB. - add telnet command "internet" & "nmask". [Improvements & Corrected Problems] - Improve PPPoE/LLC perfromance. - Correct 'adsl ppp' command issue that modulation (modu) can't be set more than four. - Improve wireless performance and coverage. - Enlarged DHCP client protocol handler buffer size up to 576 bytes. - Roll back to IDLE status when accept PPTP socket fail to prevent from occupying a virtual interface forever. - Correct a rebooting issue when set a wrong SIP account. - Correct a issue that the wrong SIP Account show in digit Map page. *********************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.6.3.1 (Formal Release) Release Date : 04th October 2006 *********************************************************************************** - Correct an issue where wireless clients can't find AP after configuring WDS. - Correct 'adsl ppp' command so modulation (modu) can be set more than four - Improve ADSL retrain issue ****************************************************************************************** Firmware Version : 2.6.3.1 Release Date : 12th Sept 2006 ****************************************************************************************** [New Functions] - Add True IP DMZ function (see www.support.draytek.co.uk for info). - Support Packet-OVERDRIVE(tm) on wireless connection. It can increase wireless performance if the wireless client also supports such technology. - The Web Content Filter (SufrControl) is supported when VPN is the default route. - Add two new adsl Telnet commands. a. "adsl showbins" to show dsl bits per bin(tone) information. b. "adsl optn dual on/off" to enable/disable dual-lantency (modem code MUST be 131701 or later). - Add more wireless messages on syslog. - Add DSL Annex Info on WUI. [Improvements & Corrected Problems] - SNMP Facility is now working correctly in all environments - Improve the PPPoE interoperability. - Correct the QoS/Firewall LED display issue. - Improve the DDNS stability. - Correct display of "path mode" and "dslam vendor information" on Telnet command "adsl status". - Improve the VPN stability on PPTP and IPSEC. ****************************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.6.2.1 Release Date : July 31, 2006 ****************************************************************************************** [New Functions] - Add telnet command for Broadsoft SIP proxy call control mode. - Add protection for "Configuration Backup / Restoration" to prevent loading wrong configuration. [Improvements & Corrected Problems] - Improve interoperability for SIP server authentication. - Correct the problem of set default limit value but causing reset current session count. - Correct the problem that ring pattern cannot work properly for SIP account after index three. - Correct the issue that answering port (FXS1 or FXS2) cannot connect to transferring call while receiving it for both ring ports (FXS1 and 2) are activated. - Correct the issue that firewall setting is unable to be restored when use "Configuration Backup / Restoration". - Correct the issue that enabling hot-line function with empty SIP URL. Note: 1. To turn on/off broadsoft call control mode, use the following telnet command: > voip sip acc n -B val // where n means 1~6 SIP account; val means 0/1 representing turn off/on. ****************************************************************************************** Release Notes for Vigor2700 series Firmware Version : 2.6.2 Release Date : June 20, 2006 ****************************************************************************************** [New Functions] - Add Bandwidth Management (limit session and limit bandwidth). - Add Wake on LAN, Ping Diagnosis and Trace Route functions. - Add Data Flow Monitor function. [Improvements & Corrected Problems] - Add switch settings for syslog message. - Add authentication setting for Mail Alert. - Added two Telnet commands "wan ppp_mru" and "wan ppp_ipcp_vso" to adjust the size of PPP LCP MRU and enable/disable PPP IPCP VSO (Vendor Specific Option). - Correct an issue that wireless function can not be re-enabled. - Correct an issue that Open Port function fails when WAN connection drops and reconnects again. - Correct vpi/vci=0 issue when download RST firmware. - Correct a reboot issue due to DPD log appeared while executing Telnet command "log -wt". - Correct an issue that router cannot get a static WAN IP from Arrakis' (British Telcom) BBRAS via PPPoA protocol even they have choose a fixed IP to the PPPoA session of WAN port. - Improve the Telnet commands "mngt noping" and "mngt defenseworm". - Improve DDNS for ChangeIP DDNS provider. - Improve the RFC-2543 interoperability. - Move the 'PSTN Setup' setting into the Dial Plan page on 2S1L model. [End of File]