DrayTek UK Users' Community Forum
Help, Advice and Solutions from DrayTek Users
AP903 with v1.4.8 - logout is broken
- ianfretwell
- Topic Author
- Offline
- Junior Member
-
Less
More
- Posts: 93
- Thank you received: 2
22 Feb 2023 11:09 #1
by ianfretwell
AP903 with v1.4.8 - logout is broken was created by ianfretwell
Two AP903's upgraded to v1.4.8 - neither of them will let me logout cleanly now. In both cases the top frame of the page breaks and essentially locks up.
It's not a big deal as you can just close the page and reload if needed - but you'd think somebody might have spotted this before release...
It's not a big deal as you can just close the page and reload if needed - but you'd think somebody might have spotted this before release...
Please Log in or Create an account to join the conversation.
- colinjmair
- Offline
- Junior Member
-
Less
More
- Posts: 52
- Thank you received: 0
22 Feb 2023 13:44 #2
by colinjmair
Replied by colinjmair on topic Re: AP903 with v1.4.8 - logout is broken
Hi,
Does the Channel Load, in the dashboard, on 1.4.8, look ok ?
I upgraded a couple of AP912C, from 1.4.7 to 1.4.8 and the Channel Load, showed 5GHz at Heavy 98%, rolled back to 1.4.7 and it changed back to Light 1%
regards
Colin
Does the Channel Load, in the dashboard, on 1.4.8, look ok ?
I upgraded a couple of AP912C, from 1.4.7 to 1.4.8 and the Channel Load, showed 5GHz at Heavy 98%, rolled back to 1.4.7 and it changed back to Light 1%
regards
Colin
Please Log in or Create an account to join the conversation.
- ianfretwell
- Topic Author
- Offline
- Junior Member
-
Less
More
- Posts: 93
- Thank you received: 2
22 Feb 2023 15:50 #3
by ianfretwell
Replied by ianfretwell on topic Re: AP903 with v1.4.8 - logout is broken
That appears fine for me.
Both my AP's are in 'AP' mode, one is wired the other is WDS.
Both my AP's are in 'AP' mode, one is wired the other is WDS.
Please Log in or Create an account to join the conversation.
- colinjmair
- Offline
- Junior Member
-
Less
More
- Posts: 52
- Thank you received: 0
22 Feb 2023 15:52 #4
by colinjmair
Replied by colinjmair on topic Re: AP903 with v1.4.8 - logout is broken
Ok thanks, I have seen elsewhere that https: access is broken with 1.4.8, http: still works.
regards
Colin
regards
Colin
Please Log in or Create an account to join the conversation.
- ianfretwell
- Topic Author
- Offline
- Junior Member
-
Less
More
- Posts: 93
- Thank you received: 2
23 Feb 2023 09:05 #5
by ianfretwell
Replied by ianfretwell on topic Re: AP903 with v1.4.8 - logout is broken
Hmmm, I have HTTP enabled but with the 'Enforce HTTPS Access' checked. Since it's working 'close-enough' I'm not gonna risk changing that to just HTTPS.
Please Log in or Create an account to join the conversation.
- ianfretwell
- Topic Author
- Offline
- Junior Member
-
Less
More
- Posts: 93
- Thank you received: 2
24 Feb 2023 09:16 #6
by ianfretwell
Replied by ianfretwell on topic Re: AP903 with v1.4.8 - logout is broken
The release notes have now been revised with this: -
Known Issue
Web access via HTTPS doesn't work well after the firmware upgrade. It is recommended
to use HTTP instead or use either of the methods below to fix this problem temporarily.
(a) Enable "Enforce HTTPS Access" on web System Maintenance >> Management.
(b) Use "https://{IP}/login.asp" to access web. (Add "/login.asp" manually after IP. For
example: "https://192.168.1.11/login.asp ")
Known Issue
Web access via HTTPS doesn't work well after the firmware upgrade. It is recommended
to use HTTP instead or use either of the methods below to fix this problem temporarily.
(a) Enable "Enforce HTTPS Access" on web System Maintenance >> Management.
(b) Use "https://{IP}/login.asp" to access web. (Add "/login.asp" manually after IP. For
example: "
Please Log in or Create an account to join the conversation.
Moderators: Sami
Copyright © 2024 DrayTek