DrayTek UK Users' Community Forum
Help, Advice and Solutions from DrayTek Users
2820 SNMP Setup
- soulkiss
- Topic Author
- Offline
- New Member
Less
More
- Posts: 3
- Thank you received: 0
12 Oct 2010 13:07 #64222
by soulkiss
2820 SNMP Setup was created by soulkiss
Hi there.
I have a 2820 that I wish to monitor from an external server using SNMP
I have set up SNMP in the Management section of the UI Configurator and rebooted twice.
Telnetting in shows the following
SNMP Agent is [Enable].
Get Community is [public].
Set Community is
I have a 2820 that I wish to monitor from an external server using SNMP
I have set up SNMP in the Management section of the UI Configurator and rebooted twice.
Telnetting in shows the following
SNMP Agent is [Enable].
Get Community is [public].
Set Community is
This message contains secure information
Please Log in or Create an account to join the conversation.
- thrain
- Offline
- Junior Member
Less
More
- Posts: 59
- Thank you received: 0
12 Oct 2010 13:39 #64224
by thrain
Replied by thrain on topic 2820 SNMP Setup
Change your SNMP strings to something that's a bit harder to guess than the standard ones :shock:
To check snmp download getifhttp://www.wtcs.org/snmp4tpc/getif.htm and try and query the WAN interface.
To check snmp download getif
Please Log in or Create an account to join the conversation.
- soulkiss
- Topic Author
- Offline
- New Member
Less
More
- Posts: 3
- Thank you received: 0
12 Oct 2010 14:14 #64226
by soulkiss
Well as this is still in testing and I AM publishing configs to the internet, I think that its probably right to just use the defaults.
To clarify, from a host on the Inside (LAN) of the router I cannot SNMP,WALK (using the standard Linux SNMP toolset) to either the LAN or WAN interfaces, both of which respond to PING/ICMP from inside.
From outside of the network (from the Amazon Cloud to be exact) is the same case, well limited to the WAN interface of course.
UPDATE: Tried GetIF now as well, still no luck.
Replied by soulkiss on topic 2820 SNMP Setup
Change your SNMP strings to something that's a bit harder to guess than the standard onesThrain wrote:
:shock:
To check snmp download getifhttp://www.wtcs.org/snmp4tpc/getif.htm and try and query the WAN interface.
Well as this is still in testing and I AM publishing configs to the internet, I think that its probably right to just use the defaults.
To clarify, from a host on the Inside (LAN) of the router I cannot SNMP,WALK (using the standard Linux SNMP toolset) to either the LAN or WAN interfaces, both of which respond to PING/ICMP from inside.
From outside of the network (from the Amazon Cloud to be exact) is the same case, well limited to the WAN interface of course.
UPDATE: Tried GetIF now as well, still no luck.
Please Log in or Create an account to join the conversation.
- gkirwan
- Offline
- New Member
Less
More
- Posts: 1
- Thank you received: 0
12 Oct 2010 20:45 #64230
by gkirwan
Replied by gkirwan on topic Same Issue
I have three 2820's that I can not connect to using PTRG but I know the routers are ok as I have 5 others at the same site which I can monitor.
Please Log in or Create an account to join the conversation.
- soulkiss
- Topic Author
- Offline
- New Member
Less
More
- Posts: 3
- Thank you received: 0
12 Oct 2010 21:42 #64232
by soulkiss
What Firmware levels do you have?
If the 5 that work are on one then maybe there is a level of firmware that SNMP is broken in
Replied by soulkiss on topic Re: Same Issue
I have three 2820's that I can not connect to using PTRG but I know the routers are ok as I have 5 others at the same site which I can monitor.GKirwan wrote:
What Firmware levels do you have?
If the 5 that work are on one then maybe there is a level of firmware that SNMP is broken in
Please Log in or Create an account to join the conversation.
Moderators: Sami
Copyright © 2024 DrayTek