DrayTek UK Users' Community Forum
Help, Advice and Solutions from DrayTek Users
How do I set up a Vigor 2820n for USB access of NAS?
- bglister
- Topic Author
- Offline
- Junior Member
Less
More
- Posts: 11
- Thank you received: 0
20 Aug 2009 21:22 #57328
by bglister
How do I set up a Vigor 2820n for USB access of NAS? was created by bglister
I'm probably being a little dense here, but I don't know how to set up my router to use attached storage via the USB port.
So far:
I have installed the latest firmware
Attached a FAT32 formatted USB memory stick - and it is reported through the router's control panel (at 192.168.1.1) as present and correct.
But how do I access this drive through Windows XP - and how do I input username and password to allow access to it.
I tried adding \\192.168.1.1 through My Netwrok Places, but it didn't work. It would nice to get this going so I could a home network drive for all PCs in the house to back up to. Just don't know how, and the suppled manual does not (obviously) cover this new future. Help please!
So far:
I have installed the latest firmware
Attached a FAT32 formatted USB memory stick - and it is reported through the router's control panel (at 192.168.1.1) as present and correct.
But how do I access this drive through Windows XP - and how do I input username and password to allow access to it.
I tried adding \\192.168.1.1 through My Netwrok Places, but it didn't work. It would nice to get this going so I could a home network drive for all PCs in the house to back up to. Just don't know how, and the suppled manual does not (obviously) cover this new future. Help please!
Please Log in or Create an account to join the conversation.
- voodle
- Offline
- Big Contributor
Less
More
- Posts: 1139
- Thank you received: 0
21 Aug 2009 09:22 #57330
by voodle
Replied by voodle on topic How do I set up a Vigor 2820n for USB access of NAS?
What happens when you try to connect to the router's IP as a network address (\\192.168.1.1) in the address bar? If it doesn't connect, you might need to turn the Samba service on first, that's under USB General settings as Samba Service(Network Neighborhood), by default it's disabled so the USB is only accessible through FTP.
It allows guest access by default but supports different users if you make some in the USB User Management section.
It allows guest access by default but supports different users if you make some in the USB User Management section.
Please Log in or Create an account to join the conversation.
- bglister
- Topic Author
- Offline
- Junior Member
Less
More
- Posts: 11
- Thank you received: 0
21 Aug 2009 16:05 #57348
by bglister
Replied by bglister on topic How do I set up a Vigor 2820n for USB access of NAS?
OK - I cannot OK using Internet Explorer or Firefox to 192.168.1.1.
If I try to add a new Network Place using \\192.168.1.1 it gives me an error message. I am a bit of a Newbie at this and could do with some hand holding. Don't really know how to set this up as a network place, but I think everything is OK on the router side of things and I have enabled Samba.
If I try to add a new Network Place using \\192.168.1.1 it gives me an error message. I am a bit of a Newbie at this and could do with some hand holding. Don't really know how to set this up as a network place, but I think everything is OK on the router side of things and I have enabled Samba.
Please Log in or Create an account to join the conversation.
- davegarratt
- Offline
- Junior Member
Less
More
- Posts: 38
- Thank you received: 0
28 Aug 2009 11:37 #57453
by davegarratt
Replied by davegarratt on topic How do I set up a Vigor 2820n for USB access of NAS?
Try adding a new network place by specifying ftp://192.168.1.1
Please Log in or Create an account to join the conversation.
- bglister
- Topic Author
- Offline
- Junior Member
Less
More
- Posts: 11
- Thank you received: 0
28 Aug 2009 12:01 #57454
by bglister
Replied by bglister on topic How do I set up a Vigor 2820n for USB access of NAS?
Thanks Dave. Well, I am another step closer!
I have set up the network place. Just can't get Windows to allow me access to it!! Argggh. "Windows cannot access this folder. Make sure you have permission etc. Parameter incorrect".
So that sounds like I don't have the right security settings in place. What is the easiest way to set this up please?
Sorry for the Q's - I'm struggling with this, but getting closer all the time.
Bryan
I have set up the network place. Just can't get Windows to allow me access to it!! Argggh. "Windows cannot access this folder. Make sure you have permission etc. Parameter incorrect".
So that sounds like I don't have the right security settings in place. What is the easiest way to set this up please?
Sorry for the Q's - I'm struggling with this, but getting closer all the time.
Bryan
Please Log in or Create an account to join the conversation.
- davegarratt
- Offline
- Junior Member
Less
More
- Posts: 38
- Thank you received: 0
28 Aug 2009 18:56 #57463
by davegarratt
Replied by davegarratt on topic How do I set up a Vigor 2820n for USB access of NAS?
I'm still trying to figure this out myself except I'm using Vista and not XP. I assume you have created users and passwords in the Vigor admin page. All you should need to do is right click on the connection you have created and select Login As .....
Please Log in or Create an account to join the conversation.
Moderators: Chris, Sami
Copyright © 2024 DrayTek