Apologies - I omitted the firmware level from previous post.
It is 3.6.4 and I have tried to use both a 2830 & 2850.
Signal strength is 50%.
I am using the APN everywhere and correct login details.
Issue - is that it is logging in and connecting, but no IP address is being allocated.
The dongle works fine if direct connected to a PC, but does seem to take a long time to initialise.

I seem to be my own particular world of pain as these settings seem to work for everyone else.
Suggestions gratefully appreciated.

morethanit wrote: Hi,

Here is my (truncated syslog)
21:44:24 WAN 3 is up.
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfAck Identifier:0x01 IP Address: 10 5 247 xxx Primary Domain Name Server......
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfReq Identifier:0x01 IP Address: 10 5 247 xxx Primary Domain Name Server.......
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfNak Identifier:0x00 IP Address: 10 5 247 xxx Primary Domain Name Server.......
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfAck Identifier:0x01 ##
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfReq Identifier:0x01 ##
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfReq Identifier:0x00 IP Address: 0 0 0 0 Primary Domain Name Server: 0 0 0 0 Secondary Domain Name Server: 0 0 0 0 ##
21:44:24 WAN3 PPPoE <== Protocol:CHAP(c223) Success Identifier:0x01 ##
21:44:24 WAN3 PPPoE ==> Protocol:CHAP(c223) Response Identifier:0x01 ......
21:44:24 WAN3 PPPoE <== Protocol:CHAP(c223) Challenge Identifier:0x01 ......
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) DiscReq Identifier:0x09Magic Number: 0x2e7 d3 d6 ##
21:44:24 WAN3 PPPoE ==> Protocol:LCP(c021) ConfAck Identifier:0x08 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfReq Identifier:0x08 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfAck Identifier:0x01 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:24 WAN3 PPPoE ==> Protocol:LCP(c021) ConfRej Identifier:0x07 Protocol Field Compression ##
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfReq Identifier:0x07 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:23 WAN3 PPPoE ==> Protocol:LCP(c021) ConfReq Identifier:0x01 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:21 [3G]Modem status:A1 20 00 00 00 00 02 00 03 00 len=10
21:44:21 [3G]Modem response: CONNECT 100000000
21:44:21 [3G]Modem dial [ATDT*99# ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem prepare to dial [AT ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem initialize2 [AT ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem initialize [AT+CGDCONT=1,'IP','everywhere' ]
21:44:21 [3G]Good. Don't need PIN code
21:44:21 [3G]Modem response: +CPIN: READY OK
21:44:21 [3G]Send command AT+CPIN?
21:44:21 [3G]Modem response: +CSQ: 26,99 OK
21:44:21 [3G]Query for signal strength AT+CSQ
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Send default init command AT&FE0V1X1&D2&C1S0=0 #1
21:44:21 WAN3 PPPoE <== Protocol:LCP(c021) ProtRej Identifier:0x06Rejected Protocol: 0x7eff .....
21:44:21 WAN3 PPPoE ==> Protocol:LCP(c021) ConfReq Identifier:0x00 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:21 WAN3 PPPoE <== V:1 T:1 PADS ID:0

morethanit wrote: Apologies - I omitted the firmware level from previous post.
It is 3.6.4 and I have tried to use both a 2830 & 2850.
Signal strength is 50%.
I am using the APN everywhere and correct login details.
Issue - is that it is logging in and connecting, but no IP address is being allocated.
The dongle works fine if direct connected to a PC, but does seem to take a long time to initialise.

I seem to be my own particular world of pain as these settings seem to work for everyone else.
Suggestions gratefully appreciated.

Hi,
As I have cancelled my 4GEE contract and have no longer any use for the Huwei 4G dongle, I am happy to sell it on. Who knows the issues are with possible different Firmware.
Just reply via PM if you are interested.